shielded power inductors C pfl1609 document 875 -1 document 875-1 revised 09/13/15 ? low cost, low profle 0603 size power inductor ? less than 1 mm high; requires less than 2 mm 2 of board space ? lower dcr than other parts this size inductance 2 dcr (mohms) 3 srf typ 4 i sat (ma) 5 i rms (ma) 6 part number 1 20% (h) typ max (mhz) 10% drop 20% drop 30% drop 20c rise 40c rise pfl1609-471me_ 0.47 83 100 650 760 990 1200 1000 1300 pfl1609-561me_ 0.56 110 130 600 710 920 1100 1100 1400 pfl1609-681me_ 0.68 145 170 520 610 780 900 1100 1400 pfl1609-102me_ 1.0 200 230 445 480 690 760 650 850 pfl1609-222me_ 2.2 410 470 130 300 390 470 480 630 pfl1609-472me_ 4.7 620 700 60 240 300 370 380 500 designers kit c433 contains 20 of each pfl1609 and pfl2010 value core material composite core and winding loss see www.coilcraft.com/coreloss environmental rohs compliant, halogen free terminations rohs compliant matte tin over nickel over silver- platinum-glass frit. other terminations available at additional cost. weight 7.9 C 8.3 mg ambient temperature C40c to +85c with (40c rise) i rms current. maximum part temperature +125c (ambient + temp rise). derating . storage temperature component: C40c to +125c. tape and reel packaging: C40c to +80c resistance to soldering heat max three 40 second refows at +260c, parts cooled to room temperature between cycles moisture sensitivity level (msl) 1 (unlimited foor life at <30c / 85% relative humidity) failures in time (fit) / mean time between failures (mtbf) 38 per billion hours / 26,315,789 hours, calculated per telcordia sr-332 packaging 2000 per 7 reel paper tape: 8 mm wide, 1.0 mm thick, 2 mm pocket spacing pcb washing tested to mil-std-202 method 215 plus an additional aqueous wash. see doc787_pcb_washing.pdf . 1. when ordering, please specify packaging codes: pfl1609-472me w packaging: w = 7 machine-ready reel. eia-481 punched paper tape (2000 parts per full reel). u = less than full reel. in tape, but not machine ready. to have a leader and trailer added ($25 charge), use code letter w instead. 2. inductance tested at 7.9 mhz, 0.1 vrms using a coilcraft smd-f test fxture with an agilent/hp 4286a impedance analyzer and coilcraft- provided correlation pieces. 3. dcr measured using a micro-ohmmeter. 4. srf measured using an agilent/hp 8753d network analyzer and a coilcraft smd-d test fxture. . dc current at 25c that causes the specifed inductance drop from its value without current. click for temperature derating information . 6. current that causes the specifed temperature rise from 25c ambient. this information is for reference only and does not represent absolute maximum ratings. click for temperature derating information . 7. electrical specifcations at 25c. refer to doc 362 soldering surface mount components before soldering.
pfl1609 series document 875-2 revised 09/13/15 document 875-2 l vs current l vs frequency te rm inal wraparound: approx 0.010/0,254 both ends recommended land p attern 0.071 1,80 0.015 0,38 0.037 0,95 max max 0.042 1,07 0.040 1,02 0.025 0,64 max 0.012 0,305 0.012 0,305 0.036 0,91 0.030 0,76 0.050 1,27 dimensions are in inches mm 0.1 1 10 11 0 1000 100 frequenc y (mhz) inductance (nh) 0.47 h 0.68 h 1.0 h 2.2 h 4.7 h 0.56 h 0.56 h 0.1 1 10 0.01 0.1 10 1 current (a) inductance (nh) 0.47 h 0.56 h 0.68 h 1.0 h 2.2 h 4.7 h
|
